Biomechanical evaluation of four surgical techniques for ventral stabilization of the atlantoaxial joint in dogs.

PURPOSE: This study compared, through biomechanical evaluation under ventral flexion load, four surgical techniques for ventral stabilization of the atlantoaxial joint in dogs. METHODS: In total, 28 identical atlantoaxial joint models were created by digital printing from computed tomography images of a dog, and the specimens were divided into four groups of seven. In each group, a different technique for ventral stabilization of the atlantoaxial joint was performed: transarticular lag screws, polyaxial screws, multiple screws and bone cement (polymethylmethacrylate-PMMA), and atlantoaxial plate. After the stabilization technique, biomechanical evaluation was performed under ventral flexion load, both with a predefined constant load and with a gradually increasing load until stabilization failure. RESULTS: All specimens, regardless of stabilization technique, were able to support the predefined load without failing. However, the PMMA method provided significant more rigidity (p ≤ 0.05) and also best resisted the gradual increase in load, supporting a significantly higher maximum force (p ≤ 0.05). There was no statistical difference in flexural strength between the transarticular lag screws and plate groups. The polyaxial screws method was significantly less resistant to loading (p ≤ 0.05) than the other groups. CONCLUSIONS: The PMMA technique had biomechanical advantages in ventral atlantoaxial stabilization over the other evaluated methods.

Biomechanical evaluation of four surgical techniques for ventral stabilization of the atlantoaxial joint in dogs

ABSTRACT Purpose: This study compared, through biomechanical evaluation under ventral flexion load, four surgical techniques for ventral stabilization of the atlantoaxial joint in dogs. Methods: In total, 28 identical atlantoaxial joint models were created by digital printing from computed tomography images of a dog, and the specimens were divided into four groups of seven. In each group, a different technique for ventral stabilization of the atlantoaxial joint was performed: transarticular lag screws, polyaxial screws, multiple screws and bone cement (polymethylmethacrylate-PMMA), and atlantoaxial plate. After the stabilization technique, biomechanical evaluation was performed under ventral flexion load, both with a predefined constant load and with a gradually increasing load until stabilization failure. Results: All specimens, regardless of stabilization technique, were able to support the predefined load without failing. However, the PMMA method provided significant more rigidity (p ≤ 0.05) and also best resisted the gradual increase in load, supporting a significantly higher maximum force (p ≤ 0.05). There was no statistical difference in flexural strength between the transarticular lag screws and plate groups. The polyaxial screws method was significantly less resistant to loading (p ≤ 0.05) than the other groups. Conclusions: The PMMA technique had biomechanical advantages in ventral atlantoaxial stabilization over the other evaluated methods.

An anatomical training model for cerebrospinal liquid collection and myelography in embalmed dog cadavers / Modelo anatômico para treinamento de colheita de líquido cerebroespinhal e mielografia em cadáveres de cães quimicamente preparados

In research and academic activities, guidelines are essential and imperative especially on the use of animals. Alternative methods that do not bring academic or scientific harm should also be sought. This study aimed to develop a training model for the collection of cerebrospinal fluid (CSF) and myelography in the cervical and lumbar regions in cadavers of embalmed dogs, using an alcoholic solution and curing salts for fixation and conservation. The dogs were divided into 4 grups of 8 animal each and stored between 2ºC and 6ºC, for 30, 60, 90, or 120 days. Durotomy was performed to implant two urethral catheters (one in the cranial direction and another in the caudal direction to the spinal cord access site), in the subduraracnoid space. This space was fixed via manual infusion of saline solution with a 20-mL syringe to simulate the presence of the CSF and the positive pressure, while the puncture was made. Four cadavers of each group were randomly selected for the CSF puncture from the atlantooccipital joint and in the lumbar region between L5 and L6, respectively, and four were used for CSF puncture training, in which radiographic contrast (myelography) was injected in the same locations. This model was cost-effective, did not utilize toxic products, and can preserve cadavers for up to 120 days. In this novel anatomical model, a maximum of 15 students can be trained on CSF puncture, allowing cervical and lumbar myelography and at least 30 perforations per cadaver.

É essencial e imperioso ter critério quanto ao uso de animais em pesquisa e atividades de ensino e, consequentemente, buscar métodos alternativos que não causem prejuízo acadêmico ou científico. Para que não ocorra deterioração dos tecidos, a fixação e conservação de peças anatômicas e cadáveres devem ser realizadas. Objetivou-se, com este estudo, desenvolver um modelo anatômico para treinamento de colheita de líquido cerebroespinhal (LCE) e mielografia, nas regiões cervical e lombar. Os cães foram divididos em quatro grupos contendo oito animais cada e armazenados entre 2ºC e 6ºC, por 30, 60, 90 ou 120 dias. Foi realizada durotomia para implantação de duas sondas uretrais, no espaço subaracnóide. A infusão manual de solução fisiológica com seringa de 20 mL foi utilizada para simular a presença do LCE e a pressão positiva, enquanto era feita a punção. Quatro cadáveres de cada grupo foram selecionados para a punção de LCE na articulação atlantooccipital e na região lombar entre L5 e L6, e quatro foram utilizados para o treinamento da punção de LCE e injeção de contraste radiográfico (mielografia). A técnica anatômica empregada possibilitou o desenvolvimento de um modelo visando ao ensino e pesquisa da radiologia em cadáveres de cães quimicamente preparados, a custo baixo e sem utilização de produtos tóxicos, mantidos sob refrigeração por 120 dias. Com isso, um máximo de 15 alunos podem ser treinados em punção do LCR, permitindo mielografia cervical e lombar com 30 perfurações por cadáver.

Three-dimensional printed poly (L-lactide) and hydroxyapatite composite for reconstruction of critical bone defect in rabbits.

PURPOSE: To use a 3D printed poly (L-lactide) acid (PLLA) and hydroxyapatite (HA) composite as a bone substitute for reconstruction of a critical bone defect in the radius of rabbits. METHODS: A 1.5 cm ostectomy was performed in the radial diaphysis of 60 New Zealand white rabbits. The rabbits were divided into three groups according to surgical treatment of the bone defect (group I - control, group II - bone graft, group III - 3D PLLA). Each group was divided into four subgroups with different radiographic and histopathologic evaluation times (T1 - 15 days, T2 - 30 days, T3 - 60 days, T4 - 90 days). RESULTS: The implant group had greater clinically lameness (p = 0.02), edema (p = 0.007), pain (p = 0.04) and more complications at the surgical site (p = 0.03). Histologically, this group showed greater congestion (p = 0.04), hemorrhage (p = 0.04) and inflammation. Osteogenesis was microscopically similar between days (p = 0.54) and treatments (p = 0.17), even though radiographically, more effective bone healing occurred in the graft group (II), with more callus and bone bridge formation. CONCLUSIONS: The customization of a 3D PLLA/HA scaffold was successful. However, in animals receiving the polymer-ceramic composite less bone callus and bone bridge was formed compared to the graft group.

Biomechanics of the fresh and conserved bovine pericardium.

The use of biological membranes in surgeries is a reality for years, and one of the most used is the bovine pericardium, so the purpose of this research is to describe the bovine pericardium's biomechanics by comparing two directions of a test, one parallel to the longitudinal heart axis and one perpendicular. 20 adult bovine pericardium were tested for the maximum rupture force and rupture elongation, collecting four samples of each pericardium direction. In phase 2, eight pericardia were conserved for 4 months in a 98% glycerine solution, and the solution in which they were submerged was microbiologically analysed monthly. The Mann-Whitney test was used; there was a very significant difference between the perpendicular and parallel groups (p = .0001). The T test showed no significant difference for the rupture elongation (p = .0938). In pericardium preserved in glycerine, the outliers were removed regarding the maximum rupture force, and a Boxcox transformation was performed (λ = 0.25). Outliers were removed for the rupture elongation, and Bartlett's test (p = .7836), and Cramer-Von Mises (p = .5033) were performed and then, the analysis of variance (p < .0001), followed by the Tukey test at 5%. In the microbiological analysis, there was no presence of microorganisms during conservation. The research has shown that the pericardium collection direction influences its resistance and it can be stored in glycerine for 4 months without losing biomechanical characteristics.

Three-dimensional printed poly (L-lactide) and hydroxyapatite composite for reconstruction of critical bone defect in rabbits

ABSTRACT Purpose To use a 3D printed poly (L-lactide) acid (PLLA) and hydroxyapatite (HA) composite as a bone substitute for reconstruction of a critical bone defect in the radius of rabbits. Methods A 1.5 cm ostectomy was performed in the radial diaphysis of 60 New Zealand white rabbits. The rabbits were divided into three groups according to surgical treatment of the bone defect (group I - control, group II - bone graft, group III - 3D PLLA). Each group was divided into four subgroups with different radiographic and histopathologic evaluation times (T1 - 15 days, T2 - 30 days, T3 - 60 days, T4 - 90 days). Results The implant group had greater clinically lameness (p = 0.02), edema (p = 0.007), pain (p = 0.04) and more complications at the surgical site (p = 0.03). Histologically, this group showed greater congestion (p = 0.04), hemorrhage (p = 0.04) and inflammation. Osteogenesis was microscopically similar between days (p = 0.54) and treatments (p = 0.17), even though radiographically, more effective bone healing occurred in the graft group (II), with more callus and bone bridge formation. Conclusions The customization of a 3D PLLA/HA scaffold was successful. However, in animals receiving the polymer-ceramic composite less bone callus and bone bridge was formed compared to the graft group.